Registered: 3 months ago
How To: Apply a Motocross Graphics Kit
Ever bought a dirt bike graphics kit to clean up your motocross bike, but been too scared to place it on for worry of destroying it in the process? Here are the secrets now we have been using for years to get graphics on quickly and easily.
What are the options?
The old saying goes there are a number of totally different ways to skin a cat, which also applies to sticker kits as there isn’t really a proper or mistaken way to do this. We've recommended the next technique as it has ended up being the best way now we have experienced while getting good outcomes, and might be cleaner than some other ways involving soapy water to help getting the graphics on straight.
Other alternatives for applying graphics to the bike utilizing nothing however elbow grease, which can work out fine, but when you haven’t applied graphics before we wouldn’t suggest it! The downside is the graphics are sticky and never very malleable, so you will have to get them straight the first attempt or you possibly can damage the kit attempting to tear them off to get them straight.
One other method is the wet application utilizing soapy water to lubricate the plastics and the sticker kit so you possibly can place the graphics on and slide them around till you will have them within the correct place. The downside is a few consider that even though the soapy water dries, there may be always soap residue the stays beneath the grime bike graphics kit, compromising the adhesive strength and making the kit more likely to peel off over time.
Step 1: Remove the old graphic kit from areas which you wish to apply graphics to, you desire a clean and smooth surface for the perfect likelihood of your graphics looking good and staying on. There could also be some glue residue left on your plastics which is best to clean off with an alcohol-based mostly cleaner - it's important to not use any oil-based cleaners, as this can damage the glue after installation.
Step 2: When your bike is clean and dry, take all your new graphics out of the packaging and work out where each piece needs to go, it may be confusing sometimes with similarly formed grime bike stickers, so an excellent way to remember is working everything out after which laying them on the ground within the pattern which they are going to go onto your bike.
Step 3: You are ready to start applying! Choose a part of the bike which is smooth and relatively flat for your first try quite than picking a rounded surface which can be tricky, we often start on the front fender and work our way to the back of the bike from there.
Some people like to remove the plastics from the bike to apply graphics, however we have discovered that on a full kit, some parts of the bike won’t line up perfectly straight, so keeping the plastics on the bike will provide help to get everything lining up straighter. Chances are you'll want to remove your seat or certain items of plastic momentarily as some graphics are designed to fold over an edge and stick down on the highest of your fuel tank for instance, which would be harder with your seat nonetheless attached.
Begin by holding the sticker to the desired location to see how well it will line up and the place you want it to stick. Once you are blissful, peel away a small section of the backing paper so you've got a small section of adhesive exposed. We always discover a straight part to start on as if you line the first part up properly the remainder of the sticker ought to line up appropriately with the plastic providing the sticker template is made well.
After you have a small section stuck to the plastic and earlier than you remove the rest of the sticker backing check to see if the sticker is lining up with the remainder of the plastic by holding it down to see the place it lines up. In case you are pleased you are ready to complete this off, if not you possibly can lift the sticker off and have another strive until you get it proper!
This is where the heat gun comes into play:
Take your heat gun or hair dryer set on a low setting and use it to warm the motocross graphics up on the edge which is being stuck down, hold the heat gun approximately 30cm from the goal as stickers are thin, in order that they don’t want a lot heat earlier than they start to melt - take your time and be careful or you will find yourself with a warped mess!
As you warm the sticker up you possibly can slowly peel the backing paper off and work the sticker down utilizing your fingers, you'll discover the sticker is soft because of the heat and can mould to the form of the plastics easily. Because of the warmth, it will likely be less likely to bubble and the sticker can stretch or compress easily and form to the shape you need it to.
Keep doing this until the sticker is completely on and it is best to have a straight, smooth sticker free from bubbles, and have no need to make use of a box cutter to trim the loose parts of your sticker kit.
Repeat this process on each panel however bear in mind a surface which is concave or convex will always be tough to apply without bubbles, some stickers for these panels come with a small section reduce out to permit for an overlap. You may must trim these further so do your best and don’t be scared to trim if need be!
When you loved this informative article and you wish to receive much more information relating to crf250l stickers assure visit our webpage.
Topics Started: 0
Replies Created: 0
Forum Role: Participant